EVOLV Corsa | Setup Guide

Modified on Wed, 26 Oct, 2022 at 4:53 PM

This start-up guide will talk you through unboxing and setting up your Corsa electric vehicle.

Step 1: Open Box

Included in the box you will find a package containing a settings guide, quality control checklist and a user manual, as well as a charger, and multi-tool.

Step 2: Unbox Your Electric Vehicle

Remove top layers of packing material to access steering column and handlebars. Using the included multi-tool, attach the handlebars to the stem.

Lift your electric scooter out of the box and onto a flat surface.

Step 3: Folding

Unfold the Corsa

Unhook the folding clasp from the deck. Unfold the steering column and straighten it out.
Slide column lock down the steering post and close the buckle to lock it in place.
Ensure the column lock is firmly secured and you've closed the buckle to lock it in place, before riding.

Fold the Corsa

Turn off the power.
Open the column lock buckle and slide the column lock upward.
Push the steering column down towards the deck and connect the folding clasp to the deck hook near the kick plate.

Step 4: Brake Check

It's good practice to check the brakes are working before riding. Pull on either brake and give the electric scooter a push forward and back ensuring that the brakes engage properly.

Step 5: Tire Pressure

Ensure both tires are inflated to 50 - 55 PSI.

Step 6: Customize Deck Pin Code Dial

Open your deck with a three digit pin code. Set your password to any three digit combination!

Unlock the dial by turning it clockwise.
In the unlock position, push a 1mm allen key or similar sized tool, into the pin code dial hole. Now engaged, spin the number dial to set a new custom pin code.
Pull the allen key out of the dial hole to lock your new pin code in.

Note: Save your pin code somewhere safe. A new code cannot be set without the current password.

(Default code is 0-0-0)

Step 7: Charging

Battery Pack inside the Corsa

Plug your charger into the wall. The charger LED will light up green, indicating there is power. The charging port is located on the left side of the deck. Open the charging port cover to connect the charger to the Corsa.

Make sure to align the pins with the socket, connect the other end to the electric scooter. Once plugged in, the charger LED will turn red, indicating your electric scooter is charging. Once charging is complete, the light will turn green.

Battery Pack outside the Corsa
Unlock deck cover with your pin code. Turn the pin code dial and lift the deck cover.
Lift the deck up to reveal two charging ports. The charger can be plugged into the battery pack as is.
Unplug the main power cord from battery pack and lift the pack out. Set aside battery pack to be charged.
Set battery pack back into electric vehicle when finished charging. Plug the main power cord back into battery pack. Close the deck and turn the pin code dial to lock it.

Step 8: Start Your Corsa

Turn the key to unlock and turn on the LCD screen. The electric vehicle will automatically turn off after

2 minutes, if not in operation.

Step 9: Deck Lights

Toggle the ON / OFF switch to turn on or off the headlights and tail lights. The taillights will flash automatically when braking.

Push the LEFT / RIGHT arrow switch to signal left or right turn signal lights.

Step 10: Changing Speed Modes

The speed mode can be changed by using the switch near the throttle and going between 1, 2, 3.

L1 - Low Speed
L2 - Medium Speed
L3 - High Speed

Step 11: Dual Motors

Press the SINGLE / DUAL button to engage the second motor in the front wheel.

Note: It’s good practice to press the SINGLE / DUAL button only when riding and in motion. Avoid starting in dual motor mode from a standstill.

Step 12: Kick Start

By default, the Corsa kick start is disabled. There is no way to adjust this.

It's good practice to kick off before pressing the throttle to start riding, and to start in speed mode 1.

Enjoy your new ride! Please wear a helmet and protective gear before riding!

Download User Manual