VSETT 9+/10+ | Setup Guide

Modified on Wed, 17 Apr at 12:06 PM

This guide will talk you through unboxing and setting up your electric scooter. The start-up guide for VSETT 9+ and 10+ models.

Step 1: Open Box

Included in the box you will find a package containing a settings guide, a quality control checklist, user manual, charger, and multi-tool.


Step 2: Unbox electric scooter

Lift your electric scooter out of the box and onto a flat surface. 


Step 3: Unfold electric scooter

  • Pull the lever down and guide the hook over the silver bar. 

  • Push the lever up and flush against the steering stem.

  • Tighten the latch screw.






Folded Scooter:

  • Screw-in the latch screw to keep the lever in place when the electric scooter is folded.

  • Ensure the hook is locked into the kick plate handlebar.





Step 4: Tighten Handlebars

Start by unfolding the handlebars until they lock into place. Finish by tightening the coloured collar.




Step 5: Tighten LCD Panel

Using the provided multi-tool, set the position of the LCD screen/throttle on the handlebar by loosening and tightening the two silver screws on the rear of the LCD. The same tool can be used to adjust and tighten your brake levers. Choose a position that is comfortable for you. Do not overtighten.


Step 6: Brake Check

It's good practice to check the brakes are working before riding. Pull on either brake and give the electric scooter a slight push forward and back ensuring that the brakes engage properly.


Step 7: Tire Pressure

Ensure both tires are inflated to 50 - 55 PSI. Use the provided valve extender, if your pump doesn't fit the scooter valve.


Step 8: Charging

Plug your charger into the wall. The charger will light up green, indicating there is power. Make sure to align the pins with the socket, connect the other end to the electric scooter. Once plugged in, the charger will turn red, indicating your electric scooter is charging. Once charging is complete, the light will turn green.


Step 9: Start your electric scooter

Hold down the power button beside the LCD for 3 seconds, then hold your NFC card over the card scanner.
Note: Please keep your NFC cards in a safe place. You can only bind new cards if your electric scooter is in an unlocked state or if you still have an old one that works.


Step 10: Deck Lights

Hold down the " + " button beside the LCD to turn on the deck lights.
To use signal blinkers, press the raised button on the handle grips.


Step 11: Changing Speed Modes

Use the " + " and " - " buttons. Toggle through speed 1 through 3. These are speed limiters and act to limit your top speed when riding.



Step 12: Dual Motors 

If your model has dual motors, press the DDM button in, to turn on the second (front) motor. In single motor mode, only the rear motor will be used. There is no indication on the LCD.
Note: When starting off from a standstill in dual motors mode, please be cautious as the acceleration may be abrupt. We recommend gradually increasing the throttle to avoid any sudden jolts.


Step 13: Sport Mode

If your model has sport mode, press the Sport button in, to give an extra burst of power. An " S " will show up in the gear section on the LCD. Sport mode gives you increased top speed and acceleration for 2 minutes before turning itself off for a cool-down period of 5 minutes.




Step 14: Kick Start

By default, our VSETT models come with kick start enabled and cruise control disabled. Please kick off before pressing the throttle to start riding.



Enjoy your new ride! Please wear a helmet and protective gear before riding!

Download VSETT Throttle Settings.



Was this article helpful?

That’s Great!

Thank you for your feedback

Sorry! We couldn't be helpful

Thank you for your feedback

Let us know how can we improve this article!

Select at least one of the reasons

Feedback sent

We appreciate your effort and will try to fix the article